Steam & Sauna Buyer's Club

 

Steamist Commercial Parts

Brands

Steamist 005-1124

Nipple, 1x3-1/2

Model
005-1124

This 1 x 3-1/2 Nipple is for use with Steamist equipment.

NOTE: To preserve the originality, operation and safety of replacement parts, this product is not returnable.

Steamist RIP-120

Replacement Control, SMC-120

Model
RIP-120

The RIP-120 is the replacement control for the discontinued Steamist SMC-120 control. It is the control only, no steam head and no control cable. This will work on the discontinued SM and TSG model steam bath generators.

NOTE: To preserve the originality, operation and safety of replacement parts, this product is not returnable.

Your Price
$210.00
Steam & Sauna Buyer's Club
  • Simple start/stop switch
  • Mode indicator light
  • Pre-set time cycle
  • Available in Polished Chrome, Brushed Nickel, Polished Nickel, Polished Brass, and Oil Rubbed Bronze designer finishes
  • Low voltage operation
  • RIP-120 control

Steamist 60821

Automatic Blowdown Tempering Valve

Model
HC-BTV

Installs into drain line as an alternative to a blowdown tank for tempering hot blowdown water. Injects cold tap water when thermal actuator senses blowdown water over 120°F. As blowdown water cools, valve reduces cold inlet flow. At approximately 110°F cold inlet is fully closed. 

  • Drain temperature compliant for plumbing code(s)
  • Fully Automatic requiring no electric
  • Clog resistant valve design
  • Modulates to conserve water
  • Effluent tempering capacity limited only by cold water flow rate through the valve
  • Blowdown Tempering Valve
Swipe horizontally to reveal full table content.
Model: HC-BTV
Water Inlet: 1 in.
Maximum Water Inlet Pressure: 125 PSIG (8.6BAR)
Maximum Temperature: 250°F (121°C)
Full open set Temperature: 120°F (49°C)
Closing Temperature: 110°F (43°C)

 

The weight or packaging of this product requires delivery by special appointment, and on a wooden pallet. 

  The driver is responsible for curbside delivery “only” and will lower the items to ground level. 

  Prior to shipping this product, we contact customers to share shipment details and discuss any extenuating delivery circumstances that may complicate or cause additional delivery expenses. 

  Our goal is to ensure your project success.

 

Steamist 002-1078

Flex Conduit Connector, Snap T90DG

Model
002-1078

This SnapT90DG Flex Conduit Connector is for use with Steamist equipment.

NOTE: To preserve the originality, operation and safety of replacement parts, this product is not returnable.

Steamist 002-1083

Conduit, Extra Flex DSL6

Model
002-1083

This DSL6 Extra Flex Conduit Connector is for use with Steamist equipment.

NOTE: To preserve the originality, operation and safety of replacement parts, this product is not returnable.

Steamist 002-2232

Screw Set, 3.25, Wall Bracket

Model
002-2232

This Set of 8 3.25" Wall Bracket Screws are for use with Steamist equipment.

NOTE: To preserve the originality, operation and safety of replacement parts, this product is not returnable.

Steamist 002-2236

Screw for SBS-101 Wood Slats, SQ

Model
002-2236

This Wood Slats Square Screw is for use with Steamist's SBS-101 Seat.

NOTE: To preserve the originality, operation and safety of replacement parts, this product is not returnable.

Steamist 002-2237-BN

Pin Cap for SBS-101, SQ, BN

Model
002-2237-BN

This Square Brushed Nickel Pin Cap is for use with Steamist's SBS-101 Seat.

NOTE: To preserve the originality, operation and safety of replacement parts, this product is not returnable.

Steamist 2237-ORB

Pin Cap for SBS-101, SQ, ORB

Model
2237-ORB

This Square Oil Rubbed Bronze Pin Cap is for use with Steamist's SBS-101 Seat.

NOTE: To preserve the originality, operation and safety of replacement parts, this product is not returnable.